Tag: Engineering

Takata Airbags: Safety or Hazard?
11th Dec 2019
Introduction: Introduction Takata is a Japanese based airbag systems supplier company (Helmold et al., 2017). An airbag is a safety device in vehicles which consists of a fabric cushion which opens up immediately w...

Thin Turbulent/Non-turbulent Interface Separating the Turbulent Region from the Irrotational Fluid
11th Dec 2019
Introduction: Abstract In this numerical study, the thin turbulent/non-turbulent interface separating the turbulent region from the irrotational fluid is studied by the means of direct numerical simulation of a de...

Resilience in Engineering Systems and its Implementation to Critical Offshore Infrastructure Systems
11th Dec 2019
Introduction: Systematic Literature Review of Resilience in Engineering Systems and its Implementation to Critical Offshore Infrastructure Systems Abstract Defining, achieving and quantifying the resilience of i...

Surface Material Effectiveness in Reducing the Impact Force of a Collision
11th Dec 2019
Introduction: Physics EEI The collision of playground surface Table of Contents 1. Introduction Hypotheses Aim 2. Background Rebounding Impulse Collision Momentum, impulse and energy conversion Newton’s sec...

Sustainability in Mechanical Engineering
11th Dec 2019
Introduction: Chapter 1. Introduction 1.1 The concept of Industrial Symbiosis Every century brings along new problems and novel solutions and the 21st century brought forth new social concerns due to the economic...

Organizational Behavior of AECOM
11th Dec 2019
Introduction: Organizational Behavior of AECOM Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3 Overview and...

Network-on-Chip (NoC) Architecture Total Power Dissipation
11th Dec 2019
Introduction: ABSTRACT The technology increase in the present world even though; a few of the power dissipation problems are thinning the technology in the field of NoC.  This power dissipation was mainly seen in...

Design of Radio Telescope System
11th Dec 2019
Introduction: Abstract This senior project aims to design a system to detect the presence of Meteors depending on the reflected radio signal. Radio telescope provides a practical and economical alternative t...

Shrinkage Prediction of Injection Molded HDPE Parts Using Artificial Neural Networks
11th Dec 2019
Introduction: Shrinkage Prediction of Injection Molded HDPE Parts Using Artificial Neural Networks Abstract Injection molding is classified as one of the most flexible and economical manufacturing processes for h...

GSM Based LPG Detection
11th Dec 2019
Introduction: ABSTRACT Our project as is entitled is aimed at avoiding the serious accidents caused by leakage of LPG gas at domestic or industrial. The main aim of achieving is resolving the  gas leakage like LP...

Voltage Unbalance on Alternators, its Effects & Solution, at Power Plants in Pakistan
10th Dec 2019
Introduction: Contents A bird’s eye view of the Network: 1.1 Introduction 1. Working of Combined Cycle Power Plants: 1.2 Major equipment of a Power Plant 1. Prime Movers: 1.3 Types of Alternators & Motors ...

Dynamic Modeling and Experimental Validation of Direct Contact Membrane Distillation (DCMD)
10th Dec 2019
Introduction: Dynamic modeling and experimental validation of Direct Contact Membrane Distillation (DCMD) using Computational fluid dynamics using and simulations ABSTRACT Direct contact membrane distillation (DCM...

Assessment of Behaviour of Strong Back System
10th Dec 2019
Introduction: CHAPTER 1 INTRODUCTION 1.1 GENERAL BACKGROUND Buildings are often subjected to lateral loads like earthquake, wind etc. So it is necessary to provide additional lateral load resisting systems to them...

Design of Solar Charge Controller Using Maximum Power Point Tracking
10th Dec 2019
Introduction: Abstract As renewable energy is becoming famous in the world due to increase in pollution, low maintenance cost, abundance of raw material, researchers and scholars are doing more research and develo...

Detecting Corrosion in Gas Pipelines
10th Dec 2019
Introduction: ABSTRACT   INTRODUCTION Gas pipeline transports the gas from a processing plant to distribution centers, under a high pressure environment which run under the ground in a safe environment.  Pipelin...

Carbon Nanofiber Reinforced Lightweight Engineered Cementitious Composites
10th Dec 2019
Introduction: Carbon Nanofiber Reinforced Lightweight Engineered Cementitious Composites Table of Contents Abstract 1.0 Introduction csdvsdvsdvs 2.0 Literature Review Introduction Historical Background of ECC Wh...

Examination of Laminar Diffusion Flames
10th Dec 2019
Introduction: Contents CHAPTER 1 INTRODUCTION Background of Study Aim and Objective Scope of Study Project Layout CHAPTER 2 LITERATURE REVIEW 2.1 Combustion and Thermochemistry 2.1.1 Basis Property Relations Exten...

Tool Wear Mechanisms in Machining of Ti-6Al-4V
10th Dec 2019
Introduction: Investigating Tool Wear Mechanisms in Machining of Ti-6Al-4V Using Coolant, Dry and Minimum Quantity Lubrication (MQL) Conditions Abstract The objective of this study is to identify and explain the ...

Ethics and Professionalism in Engineering
10th Dec 2019
Introduction: You are assigned by your employer to prospect an area for an extractable material. However, in the course of your work, you discover no such object material but some other valuable material which you...

Thermoplastic Composites with High Mechanical Properties and a Low Processing Temperature
10th Dec 2019
Introduction: Chapter 1   Introduction 1.1 Background Fibre reinforced polymer composites have been widely used in aerospace, automobile,  military, and energy applications because of their superior performance...

Effect the Percentage of Carbon Black Filler Loading to the Rubber Bearing as Base Isolation System
10th Dec 2019
Introduction: Effect The Percentage Of Carbon Black Filler Loading To The Rubber Bearing As Base Isolation System   Abstract. This research focus’ on the finding of the suitable amount of filler that need t...

Electrical Discharge Machining (EDM) Process
10th Dec 2019
Introduction: Advanced Manufacturing Processes Lab Reports Contents Contents Electrical Discharge Machining (EDM) Introduction Basic Structure of Sodick AP3L Typical Tooling System Dielectric Type and Flushing M...

Structural Strength Assessment of Civil Infrastructure
10th Dec 2019
Introduction: 1.Abstract Structural strength assessment of civil infrastructure is a prior concern to the engineers. This paper presents laboratories study as well as on site study data analysis gathered by many a...

Vehicle Stability Control Systems
10th Dec 2019
Introduction: 1 To respect the design of the well tuned passive vehicle, the proposed controller will not stabilize the vehicle during steady state maneuvers. So no ZSS for the whole operating range of the vehicle...

Analytical Study of the Interaction Between Hydraulic Fracture and the Natural Interface
10th Dec 2019
Introduction: Table of Contents Executive Summary Acknowledgements Table of Contents Table of Figures Nomenclature............................................................... Chapter 1: Hydraulic Fracturin...